Bit Error Location Analyzer Automation Commands

The Bit Error Location Analyzer automation commands are grouped into multiple categories.  Here are the list of automation commands for operating the Bit Error Location Analyzer: 



Basic: [Category] Basic ELA Application

    Basic:BasicReport..........[Property] Basic Ela report of 24 things, String, (RO, NoQuote)

    Basic:Bits.................[Property] Bit Count Result, LongLong[3], (RO, Comma)

    Basic:Capture..............[Property] Capture rate, Double[3], %, (RO)

    Basic:CBER.................[Property] Captured BER, Double[3], (RO)

    Basic:CSER.................[Property] Captured SER, Double[3], (RO)

    Basic:Enabled..............[Property] Enable processor, Bool[3], (RO)

    Basic:Errors...............[Property] Bit Errors Count Result, LongLong[3], (RO, Comma)

    Basic:Pattern..............[Property] Pattern Type, Enum[3] <AllZeros, AllOnes, Prbs7, InvPrbs7, Prbs11, InvPrbs11, Prbs13, InvPrbs13, Prbs15, InvPrbs15, Prbs20, InvPrbs20, Prbs23, InvPrbs23, Prbs31, InvPrbs31, RamGrab, InvRamGrab, RamShift, InvRamShift, None, Unknown>, (RO)

    Basic:PhaseFound...........[Property] Pattern Phase Found, Bool[3], (RO)

    Basic:ResyncCount..........[Property] Resync Count Result, Int[3], (RO, Comma)

    Basic:Status...............[Property] Ela Status, Enum[3] <NotAvail, Disabled, Stopped, Running>, (RO)

    Basic:SymbolSize...........[Property] Symbol Size, Int[3], bits, (RO)

  

Block: [Category] Block ELA Application

    Block:Ch0: [Category] Ch0 Category, (IsClass)

      Block:Ch0:Binary.........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Block:Ch0:Bins...........[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Block:Ch0:BlockSize......[Property] Block Size, Int, (RO)

      Block:Ch0:Bottom.........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Block:Ch0:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Block:Ch0:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Block:Ch0:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Block:Ch0:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Block:Ch0:Enabled........[Property] Enable processor, Bool, (RO)

      Block:Ch0:Height.........[Property] Chart Height, Double, 1 to 2147483647, 

      Block:Ch0:History........[Property] Histogram history length, Int, 0 to 100000

      Block:Ch0:HReport........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Block:Ch0:HSeq...........[Property] Histogram Sequence number, Int, (RO, NoSave)

      Block:Ch0:Left...........[Property] Chart Left, Double, 0 to 100000000000000, 

      Block:Ch0:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Block:Ch0:Locked.........[Property] Chart Locked, Bool

      Block:Ch0:Logscale.......[Property] Chart LogScale, Bool

      Block:Ch0:Offset.........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Block:Ch0:Report.........[Property] Report-Total,Squelched,Processed,InErr,Max,Avg,Rate, String, (RO, NoQuote)

      Block:Ch0:Resol..........[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Block:Ch0:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Block:Ch0:ShowMemory.....[Property] Show memories, Bool

      Block:Ch0:ShowOverlays...[Property] Show overlays, Bool

      Block:Ch0:ShowSettings...[Property] Show Settings, Bool, (NoSave)

      Block:Ch0:Status.........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Block:Ch0:Title..........[Property] Chart Title, String, (RO)

      Block:Ch0:Width..........[Property] Chart Width, Double, 1 to 100000000000000, 

      Block:Ch0:Csv............[Method] Download CSV File (HasPathResponse)

      Block:Ch0:Fit............[Method] Fit chart to data

      Block:Ch0:MapRange.......[Method] Map histogram to fit range

      Block:Ch0:Reset..........[Method] Reset chart

    Block:Ch1: [Category] Ch1 Category, (IsClass)

      Block:Ch1:Binary.........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Block:Ch1:Bins...........[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Block:Ch1:BlockSize......[Property] Block Size, Int, (RO)

      Block:Ch1:Bottom.........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Block:Ch1:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Block:Ch1:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Block:Ch1:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Block:Ch1:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Block:Ch1:Enabled........[Property] Enable processor, Bool, (RO)

      Block:Ch1:Height.........[Property] Chart Height, Double, 1 to 2147483647, 

      Block:Ch1:History........[Property] Histogram history length, Int, 0 to 100000

      Block:Ch1:HReport........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Block:Ch1:HSeq...........[Property] Histogram Sequence number, Int, (RO, NoSave)

      Block:Ch1:Left...........[Property] Chart Left, Double, 0 to 100000000000000, 

      Block:Ch1:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Block:Ch1:Locked.........[Property] Chart Locked, Bool

      Block:Ch1:Logscale.......[Property] Chart LogScale, Bool

      Block:Ch1:Offset.........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Block:Ch1:Report.........[Property] Report-Total,Squelched,Processed,InErr,Max,Avg,Rate, String, (RO, NoQuote)

      Block:Ch1:Resol..........[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Block:Ch1:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Block:Ch1:ShowMemory.....[Property] Show memories, Bool

      Block:Ch1:ShowOverlays...[Property] Show overlays, Bool

      Block:Ch1:ShowSettings...[Property] Show Settings, Bool, (NoSave)

      Block:Ch1:Status.........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Block:Ch1:Title..........[Property] Chart Title, String, (RO)

      Block:Ch1:Width..........[Property] Chart Width, Double, 1 to 100000000000000, 

      Block:Ch1:Csv............[Method] Download CSV File (HasPathResponse)

      Block:Ch1:Fit............[Method] Fit chart to data

      Block:Ch1:MapRange.......[Method] Map histogram to fit range

      Block:Ch1:Reset..........[Method] Reset chart

    Block:Cmb: [Category] Combined Category, (IsClass)

      Block:Cmb:Binary.........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Block:Cmb:Bins...........[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Block:Cmb:BlockSize......[Property] Block Size, Int, (RO)

      Block:Cmb:Bottom.........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Block:Cmb:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Block:Cmb:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Block:Cmb:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Block:Cmb:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Block:Cmb:Enabled........[Property] Enable processor, Bool, (RO)

      Block:Cmb:Height.........[Property] Chart Height, Double, 1 to 2147483647, 

      Block:Cmb:History........[Property] Histogram history length, Int, 0 to 100000

      Block:Cmb:HReport........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Block:Cmb:HSeq...........[Property] Histogram Sequence number, Int, (RO, NoSave)

      Block:Cmb:Left...........[Property] Chart Left, Double, 0 to 100000000000000, 

      Block:Cmb:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Block:Cmb:Locked.........[Property] Chart Locked, Bool

      Block:Cmb:Logscale.......[Property] Chart LogScale, Bool

      Block:Cmb:Offset.........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Block:Cmb:Report.........[Property] Report-Total,Squelched,Processed,InErr,Max,Avg,Rate, String, (RO, NoQuote)

      Block:Cmb:Resol..........[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Block:Cmb:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Block:Cmb:ShowMemory.....[Property] Show memories, Bool

      Block:Cmb:ShowOverlays...[Property] Show overlays, Bool

      Block:Cmb:ShowSettings...[Property] Show Settings, Bool, (NoSave)

      Block:Cmb:Status.........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Block:Cmb:Title..........[Property] Chart Title, String, (RO)

      Block:Cmb:Width..........[Property] Chart Width, Double, 1 to 100000000000000, 

      Block:Cmb:Csv............[Method] Download CSV File (HasPathResponse)

      Block:Cmb:Fit............[Method] Fit chart to data

      Block:Cmb:MapRange.......[Method] Map histogram to fit range

      Block:Cmb:Reset..........[Method] Reset chart

  

Burst: [Category] Burst ELA Application

    Burst:Ch0: [Category] Ch0 Category, (IsClass)

      Burst:Ch0:Binary.........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Burst:Ch0:Bins...........[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Burst:Ch0:Bottom.........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Burst:Ch0:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Burst:Ch0:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Burst:Ch0:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Burst:Ch0:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Burst:Ch0:Enabled........[Property] Enable processor, Bool, (RO)

      Burst:Ch0:Height.........[Property] Chart Height, Double, 1 to 2147483647, 

      Burst:Ch0:History........[Property] Histogram history length, Int, 0 to 100000

      Burst:Ch0:HReport........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Burst:Ch0:HSeq...........[Property] Histogram Sequence number, Int, (RO, NoSave)

      Burst:Ch0:Left...........[Property] Chart Left, Double, 0 to 100000000000000, 

      Burst:Ch0:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Burst:Ch0:Locked.........[Property] Chart Locked, Bool

      Burst:Ch0:Logscale.......[Property] Chart LogScale, Bool

      Burst:Ch0:Offset.........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Burst:Ch0:Resol..........[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Burst:Ch0:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Burst:Ch0:Separation.....[Property] Minimum Efi, Int, 1 to 4294967295

      Burst:Ch0:ShowMemory.....[Property] Show memories, Bool

      Burst:Ch0:ShowOverlays...[Property] Show overlays, Bool

      Burst:Ch0:ShowSettings...[Property] Show Settings, Bool, (NoSave)

      Burst:Ch0:Status.........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Burst:Ch0:Title..........[Property] Chart Title, String, (RO)

      Burst:Ch0:Width..........[Property] Chart Width, Double, 1 to 100000000000000, 

      Burst:Ch0:Csv............[Method] Download CSV File (HasPathResponse)

      Burst:Ch0:Fit............[Method] Fit chart to data

      Burst:Ch0:MapRange.......[Method] Map histogram to fit range

      Burst:Ch0:Reset..........[Method] Reset chart

    Burst:Ch1: [Category] Ch1 Category, (IsClass)

      Burst:Ch1:Binary.........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Burst:Ch1:Bins...........[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Burst:Ch1:Bottom.........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Burst:Ch1:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Burst:Ch1:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Burst:Ch1:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Burst:Ch1:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Burst:Ch1:Enabled........[Property] Enable processor, Bool, (RO)

      Burst:Ch1:Height.........[Property] Chart Height, Double, 1 to 2147483647, 

      Burst:Ch1:History........[Property] Histogram history length, Int, 0 to 100000

      Burst:Ch1:HReport........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Burst:Ch1:HSeq...........[Property] Histogram Sequence number, Int, (RO, NoSave)

      Burst:Ch1:Left...........[Property] Chart Left, Double, 0 to 100000000000000, 

      Burst:Ch1:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Burst:Ch1:Locked.........[Property] Chart Locked, Bool

      Burst:Ch1:Logscale.......[Property] Chart LogScale, Bool

      Burst:Ch1:Offset.........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Burst:Ch1:Resol..........[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Burst:Ch1:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Burst:Ch1:Separation.....[Property] Minimum Efi, Int, 1 to 4294967295

      Burst:Ch1:ShowMemory.....[Property] Show memories, Bool

      Burst:Ch1:ShowOverlays...[Property] Show overlays, Bool

      Burst:Ch1:ShowSettings...[Property] Show Settings, Bool, (NoSave)

      Burst:Ch1:Status.........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Burst:Ch1:Title..........[Property] Chart Title, String, (RO)

      Burst:Ch1:Width..........[Property] Chart Width, Double, 1 to 100000000000000, 

      Burst:Ch1:Csv............[Method] Download CSV File (HasPathResponse)

      Burst:Ch1:Fit............[Method] Fit chart to data

      Burst:Ch1:MapRange.......[Method] Map histogram to fit range

      Burst:Ch1:Reset..........[Method] Reset chart

    Burst:Cmb: [Category] Combined Category, (IsClass)

      Burst:Cmb:Binary.........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Burst:Cmb:Bins...........[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Burst:Cmb:Bottom.........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Burst:Cmb:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Burst:Cmb:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Burst:Cmb:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Burst:Cmb:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Burst:Cmb:Enabled........[Property] Enable processor, Bool, (RO)

      Burst:Cmb:Height.........[Property] Chart Height, Double, 1 to 2147483647, 

      Burst:Cmb:History........[Property] Histogram history length, Int, 0 to 100000

      Burst:Cmb:HReport........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Burst:Cmb:HSeq...........[Property] Histogram Sequence number, Int, (RO, NoSave)

      Burst:Cmb:Left...........[Property] Chart Left, Double, 0 to 100000000000000, 

      Burst:Cmb:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Burst:Cmb:Locked.........[Property] Chart Locked, Bool

      Burst:Cmb:Logscale.......[Property] Chart LogScale, Bool

      Burst:Cmb:Offset.........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Burst:Cmb:Resol..........[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Burst:Cmb:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Burst:Cmb:Separation.....[Property] Minimum Efi, Int, 1 to 4294967295

      Burst:Cmb:ShowMemory.....[Property] Show memories, Bool

      Burst:Cmb:ShowOverlays...[Property] Show overlays, Bool

      Burst:Cmb:ShowSettings...[Property] Show Settings, Bool, (NoSave)

      Burst:Cmb:Status.........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Burst:Cmb:Title..........[Property] Chart Title, String, (RO)

      Burst:Cmb:Width..........[Property] Chart Width, Double, 1 to 100000000000000, 

      Burst:Cmb:Csv............[Method] Download CSV File (HasPathResponse)

      Burst:Cmb:Fit............[Method] Fit chart to data

      Burst:Cmb:MapRange.......[Method] Map histogram to fit range

      Burst:Cmb:Reset..........[Method] Reset chart

  

Const: [Category] Constants, (IsClass)

    Const:Options..............[Property] Option Code, String, (RO, NoEvent, NoSave)

    Const:SN...................[Property] Serial Number, String, (RO, NoEvent, NoSave)


Data: [Category] Data Application

    Data:BitsFmt...............[Property] Data Bits Format, Enum <Scientific, Decimal>

    Data:DataRate..............[Property] Data Rate, Double, GHz, (RO)

    Data:DataLinkMode..........[Property] Data Link Mode, Enum <Ch0, Ch1, Unlinked, Interleaved>, (RO)

    Data:DataShowAllCh.........[Property] Data Show All Channels, Bool, (RO)

    Data:Elapsed...............[Property] Elapsed Time Seconds, Double, sec, (RO)

    Data:Running...............[Property] Running state, Enum <Stop, Run, RunOnce>, (RO)

    Data:Sequence..............[Property] Run Sequence, Int, (RO, Comma)

    Data:ShowSettings..........[Property] Show Settings, Bool, (NoSave)

    Data:SymbolSize............[Property] Global bits per symbol, Int[3], 1 to 10, bits

    Data:Transfer..............[Property] Bytes per second, Double, bytes/sec, (RO)

    Data:Csv...................[Method] Save ELA Results in CSV file (HasPathResponse)

    Data:Common: [Category] Data Common processor

      Data:Common:Bits.........[Property] Common bit count, LongLong, (RO, Comma)

      Data:Common:Buffers......[Property] Number of buffers, Int, (RO)

      Data:Common:Enabled......[Property] Common Enable processor, Bool, (RO)

      Data:Common:MarkDensity..[Property] Common mark density, Double, %, (RO)

      Data:Common:Marks........[Property] Common mark count, LongLong, (RO, Comma)

      Data:Common:Status.......[Property] Common Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)


ED: [Category] Pela Error Detector Access

    ED:AutoClockMsg............[Property] Autoset clock results, String, (RO)

    ED:AutoDataMsg.............[Property] Autoset data results, String, (RO)

    ED:AutoResync..............[Property] Auto Resync Enable, Bool[2]

    ED:AuxIn1..................[Property] Aux-1 input, Enum <Marker>

    ED:AuxIn2..................[Property] Aux-2 input, Enum <Blanking>

    ED:AuxOut1.................[Property] Aux-1 output, Enum <Ch0Pattern, Ch1Pattern, Ch0Error, Ch1Error, AnyError, WordClock, AuxLoopback, Off>

    ED:AuxOut2.................[Property] Aux-2 output, Enum <Ch0Pattern, Ch1Pattern, Ch0Error, Ch1Error, AnyError, WordClock, AuxLoopback, Off>

    ED:DataRate................[Property] Data Rate, Double, GHz, (RO)

    ED:ClockRate...............[Property] Input Clock Rate, Double, GHz, (RO)

    ED:ClockThresh.............[Property] Clock threshold, Double, -600.000 to 600.000, mV

    ED:ClockType...............[Property] Clock Type, Enum <Fullrate, Halfrate>

    ED:Delay...................[Property] Delay, Double[2], 0.000 to 140.000, ps

    ED:DetPatt.................[Property] Detected Pattern, Enum[2] <AllZeros, AllOnes, Prbs7, InvPrbs7, Prbs11, InvPrbs11, Prbs13, InvPrbs13, Prbs15, InvPrbs15, Prbs20, InvPrbs20, Prbs23, InvPrbs23, Prbs31, InvPrbs31, RamGrab, InvRamGrab, RamShift, InvRamShift, None, Unknown>, (RO)

    ED:DetShift................[Property] Detected Shift, Int[2], (RO)

    ED:GrayCode................[Property] Using Gray Coding (MSB=Ch1, LSB=Ch0), Bool

    ED:InSync..................[Property] In Sync Flag, Bool[3], (RO)

    ED:LinkMode................[Property] Link Mode, Enum <Ch0, Ch1, Unlinked, Interleaved>

    ED:ManualAmount............[Property] Manual Shift Amount, Int[2], -63 to 64

    ED:ManualShift.............[Property] Manual Shift Enable, Bool

    ED:OperatingRate...........[Property] Operating Clock Rate, Double, GHz, (RO)

    ED:Patt....................[Property] Detector Pattern, Enum[2] <AllZeros, AllOnes, Prbs7, InvPrbs7, Prbs11, InvPrbs11, Prbs13, InvPrbs13, Prbs15, InvPrbs15, Prbs20, InvPrbs20, Prbs23, InvPrbs23, Prbs31, InvPrbs31, RamGrab, InvRamGrab, RamShift, InvRamShift, Auto, Unknown>

    ED:ResyncThresh............[Property] Resync Threshold, Int[2], 0 to 255, (Comma)

    ED:ShowAllCh...............[Property] Show All Channels, Bool

    ED:Thresh..................[Property] Threshold, Double[2], -600.000 to 600.000, mV

    ED:UserWords...............[Property] User words, Int[2], 3 to 127, words, (Comma)

    ED:UsingEye................[Property] Using Eye Diagramming, Bool, (RO)

    ED:AutosetData.............[Method] Perform Data Autoset

    ED:ResetClock..............[Method] Reset Clocking

    ED:Resync..................[Method] Manual Resync

    ED:SetDefaults.............[Method] Set Channel Defaults


Efi: [Category] Efi ELA Application

    Efi:Ch0: [Category] Ch0 Category, (IsClass)

      Efi:Ch0:Binary...........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Efi:Ch0:Bins.............[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Efi:Ch0:Bottom...........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Efi:Ch0:CursAvail........[Property] Chart Cursor Available, Bool[11], (RO)

      Efi:Ch0:CursEnabled......[Property] Chart Cursor Enabled, Bool[11]

      Efi:Ch0:CursLabel........[Property] Chart Cursor Label, String[11], (RO)

      Efi:Ch0:CursValue........[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Efi:Ch0:Enabled..........[Property] Enable processor, Bool, (RO)

      Efi:Ch0:Height...........[Property] Chart Height, Double, 1 to 2147483647, 

      Efi:Ch0:History..........[Property] Histogram history length, Int, 0 to 100000

      Efi:Ch0:HReport..........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Efi:Ch0:HSeq.............[Property] Histogram Sequence number, Int, (RO, NoSave)

      Efi:Ch0:Left.............[Property] Chart Left, Double, 0 to 100000000000000, 

      Efi:Ch0:Limits...........[Property] Chart Limits (LRBT), Double[4], (RO)

      Efi:Ch0:Locked...........[Property] Chart Locked, Bool

      Efi:Ch0:Logscale.........[Property] Chart LogScale, Bool

      Efi:Ch0:Offset...........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Efi:Ch0:Resol............[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Efi:Ch0:Scroll...........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Efi:Ch0:ShowMemory.......[Property] Show memories, Bool

      Efi:Ch0:ShowOverlays.....[Property] Show overlays, Bool

      Efi:Ch0:ShowSettings.....[Property] Show Settings, Bool, (NoSave)

      Efi:Ch0:Status...........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Efi:Ch0:Title............[Property] Chart Title, String, (RO)

      Efi:Ch0:Width............[Property] Chart Width, Double, 1 to 100000000000000, 

      Efi:Ch0:Csv..............[Method] Download CSV File (HasPathResponse)

      Efi:Ch0:Fit..............[Method] Fit chart to data

      Efi:Ch0:MapRange.........[Method] Map histogram to fit range

      Efi:Ch0:Reset............[Method] Reset chart

    Efi:Ch1: [Category] Ch1 Category, (IsClass)

      Efi:Ch1:Binary...........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Efi:Ch1:Bins.............[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Efi:Ch1:Bottom...........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Efi:Ch1:CursAvail........[Property] Chart Cursor Available, Bool[11], (RO)

      Efi:Ch1:CursEnabled......[Property] Chart Cursor Enabled, Bool[11]

      Efi:Ch1:CursLabel........[Property] Chart Cursor Label, String[11], (RO)

      Efi:Ch1:CursValue........[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Efi:Ch1:Enabled..........[Property] Enable processor, Bool, (RO)

      Efi:Ch1:Height...........[Property] Chart Height, Double, 1 to 2147483647, 

      Efi:Ch1:History..........[Property] Histogram history length, Int, 0 to 100000

      Efi:Ch1:HReport..........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Efi:Ch1:HSeq.............[Property] Histogram Sequence number, Int, (RO, NoSave)

      Efi:Ch1:Left.............[Property] Chart Left, Double, 0 to 100000000000000, 

      Efi:Ch1:Limits...........[Property] Chart Limits (LRBT), Double[4], (RO)

      Efi:Ch1:Locked...........[Property] Chart Locked, Bool

      Efi:Ch1:Logscale.........[Property] Chart LogScale, Bool

      Efi:Ch1:Offset...........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Efi:Ch1:Resol............[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Efi:Ch1:Scroll...........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Efi:Ch1:ShowMemory.......[Property] Show memories, Bool

      Efi:Ch1:ShowOverlays.....[Property] Show overlays, Bool

      Efi:Ch1:ShowSettings.....[Property] Show Settings, Bool, (NoSave)

      Efi:Ch1:Status...........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Efi:Ch1:Title............[Property] Chart Title, String, (RO)

      Efi:Ch1:Width............[Property] Chart Width, Double, 1 to 100000000000000, 

      Efi:Ch1:Csv..............[Method] Download CSV File (HasPathResponse)

      Efi:Ch1:Fit..............[Method] Fit chart to data

      Efi:Ch1:MapRange.........[Method] Map histogram to fit range

      Efi:Ch1:Reset............[Method] Reset chart

    Efi:Cmb: [Category] Combined Category, (IsClass)

      Efi:Cmb:Binary...........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Efi:Cmb:Bins.............[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Efi:Cmb:Bottom...........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Efi:Cmb:CursAvail........[Property] Chart Cursor Available, Bool[11], (RO)

      Efi:Cmb:CursEnabled......[Property] Chart Cursor Enabled, Bool[11]

      Efi:Cmb:CursLabel........[Property] Chart Cursor Label, String[11], (RO)

      Efi:Cmb:CursValue........[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Efi:Cmb:Enabled..........[Property] Enable processor, Bool, (RO)

      Efi:Cmb:Height...........[Property] Chart Height, Double, 1 to 2147483647, 

      Efi:Cmb:History..........[Property] Histogram history length, Int, 0 to 100000

      Efi:Cmb:HReport..........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Efi:Cmb:HSeq.............[Property] Histogram Sequence number, Int, (RO, NoSave)

      Efi:Cmb:Left.............[Property] Chart Left, Double, 0 to 100000000000000, 

      Efi:Cmb:Limits...........[Property] Chart Limits (LRBT), Double[4], (RO)

      Efi:Cmb:Locked...........[Property] Chart Locked, Bool

      Efi:Cmb:Logscale.........[Property] Chart LogScale, Bool

      Efi:Cmb:Offset...........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Efi:Cmb:Resol............[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Efi:Cmb:Scroll...........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Efi:Cmb:ShowMemory.......[Property] Show memories, Bool

      Efi:Cmb:ShowOverlays.....[Property] Show overlays, Bool

      Efi:Cmb:ShowSettings.....[Property] Show Settings, Bool, (NoSave)

      Efi:Cmb:Status...........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Efi:Cmb:Title............[Property] Chart Title, String, (RO)

      Efi:Cmb:Width............[Property] Chart Width, Double, 1 to 100000000000000, 

      Efi:Cmb:Csv..............[Method] Download CSV File (HasPathResponse)

      Efi:Cmb:Fit..............[Method] Fit chart to data

      Efi:Cmb:MapRange.........[Method] Map histogram to fit range

      Efi:Cmb:Reset............[Method] Reset chart


Ela: [Category] Pela ELA Application

    Ela:BitOrder...............[Property] Ela Bit ordering, Enum <MsbFirst, LsbFirst>

    Ela:BitsFmt................[Property] Ela Bits Format, Enum <Scientific, Decimal>

    Ela:BlockSize..............[Property] Global symbols per block, Int[3], Min 1, symbols

    Ela:ElaDataRate............[Property] Ela Data Rate, Double, GHz, (RO)

    Ela:ElaLinkMode............[Property] Ela Link Mode, Enum <Ch0, Ch1, Unlinked, Interleaved>, (RO)

    Ela:Elapsed................[Property] Elapsed Time Seconds, Double, sec, (RO)

    Ela:ElaReport..............[Property] Ela report of 10 things, String, (RO, NoQuote)

    Ela:ElaShowAllCh...........[Property] Ela Show All Channels, Bool, (RO)

    Ela:File...................[Property] Ela Filename, String

    Ela:LimitMB................[Property] File Limit MB, Int, 0 to 102400, MB, (Comma)

    Ela:RecordOnly.............[Property] ELA Record Only flag, Bool

    Ela:Running................[Property] Running state, Enum <Stop, Run, RunOnce>, (RO)

    Ela:Sequence...............[Property] Run Sequence, Int, (RO, Comma)

    Ela:ShowSettings...........[Property] Show Settings, Bool, (NoSave)

    Ela:SizeMB.................[Property] File size MB, Double, MB, (RO, Comma)

    Ela:SymbolSize.............[Property] Global bits per symbol, Int[3], 1 to 128, bits

    Ela:Transfer...............[Property] Bytes per second, Double, bytes/sec, (RO)

    Ela:Csv....................[Method] Save ELA Results in CSV file (HasPathResponse)

    Ela:Common: [Category] Ela Common processor

      Ela:Common:Capture.......[Property] Common Capture percentage, Double, %, (RO)

      Ela:Common:Enabled.......[Property] Common Enable processor, Bool, (RO)

      Ela:Common:Events........[Property] Event Count M,R,S,B,P, Int[5], (RO)

      Ela:Common:LongRecords...[Property] Long Record Count, LongLong, (RO, Comma)

      Ela:Common:MediumRecords.[Property] Medium Record Count, LongLong, (RO, Comma)

      Ela:Common:ResyncLev.....[Property] Resynchronization Level, Bool, (RO)

      Ela:Common:ShortRecords..[Property] Short Record Count, LongLong, (RO, Comma)

      Ela:Common:Status........[Property] Common Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)


Err: [Category] Error Rate Application

    Err:ABER...................[Property] Accumulated BER Result, Double[3], (RO)

    Err:BerReport..............[Property] Ber report of 15 things, String, (RO, NoQuote)

    Err:Binary.................[Property] Binary Data, float[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

    Err:Bits...................[Property] Bit Count Result, LongLong[3], (RO, Comma)

    Err:BitsFmt................[Property] ED Bits Format, Enum <Scientific, Decimal>

    Err:Elapsed................[Property] Elapsed Time Seconds, Double, sec, (RO)

    Err:Errors.................[Property] Bit Errors Count Result, LongLong[3], (RO, Comma)

    Err:IBER...................[Property] Instantaneous BER Result, Double[3], (RO)

    Err:ResyncCount............[Property] Resync Count, LongLong[3], (RO, Comma)

    Err:Running................[Property] Running state, Enum <Stop, Run, RunOnce>, (RO)

    Err:Sequence...............[Property] Run Sequence, Int, (RO, Comma)

    Err:Serial.................[Property] Serial Number of Integration, Int, (RO)

    Err:ShowSettings...........[Property] Show Settings, Bool, (NoSave)

    Err:ShowStripSettings......[Property] Show Strip Chart Settings, Bool, (NoSave)

    Err:Csv....................[Method] PelaED Csv (HasPathResponse)

    Err:Csv2...................[Method] PelaErr Csv (HasPathResponse)

    Err:Fit....................[Method] PelaED Chart Fit

    Err:Reset..................[Method] Reset position

    Err:Cfg: [Category] Configuration, (IsClass)

      Err:Cfg:Interval.........[Property] Update interval, Double, 1.0 to 10000.0, sec

      Err:Cfg:Reclen...........[Property] Record Length, Int, 10 to 3000

    Err:Chart: [Category] Chart View, (IsClass)

      Err:Chart:Bottom.........[Property] Chart Bottom, Double, -99.000000 to 0.000000, LogBER, (NoSave)

      Err:Chart:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Err:Chart:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Err:Chart:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Err:Chart:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Err:Chart:Height.........[Property] Chart Height, Double, 1.000000 to 99.000000, LogBER, (NoSave)

      Err:Chart:Left...........[Property] Chart Left, Double, 0 to 100000000, sec, (NoSave)

      Err:Chart:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Err:Chart:Locked.........[Property] Chart Locked, Bool

      Err:Chart:Logscale.......[Property] Chart LogScale, Bool

      Err:Chart:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Err:Chart:ShowMemory.....[Property] Show memories, Bool

      Err:Chart:ShowOverlays...[Property] Show overlays, Bool

      Err:Chart:Title..........[Property] Chart Title, String, (RO)

      Err:Chart:Width..........[Property] Chart Width, Double, 1 to 100000000, sec, (NoSave)


Eye: [Category] Pela Eye Application

    Eye:Elapsed................[Property] Elapsed Time Seconds, Double, sec, (RO)

    Eye:Running................[Property] Running state, Enum <Stop, Run, RunOnce>, (RO)

    Eye:Sequence...............[Property] Run Sequence, Int, (RO, Comma)

    Eye:ShowSettings...........[Property] Show gui settings panel, Bool, (NoSave)

    Eye:Fit....................[Method] Fit chart

    Eye:Reset..................[Method] Reset position

    Eye:Cfg: [Category] Configuration Settings, (IsClass)

      Eye:Cfg:Bottom...........[Property] Acquisition Voltage bottom, Double, (RO)

      Eye:Cfg:Bright...........[Property] Image Brightness, Double, 0.00 to 100.00

      Eye:Cfg:Columns..........[Property] Columns in Image, Int, 10 to 1000

      Eye:Cfg:DelaySettle......[Property] Delay Settle Time, Int, 1 to 10, usec

      Eye:Cfg:Depth............[Property] E2 Depth, Double, 400000 to 10000000, bits

      Eye:Cfg:Divisions........[Property] Number of divisions H,V, Int[2], 2 to 50

      Eye:Cfg:EyeSync..........[Property] Eye Sync mode, Bool, (RO)

      Eye:Cfg:FloorNoSync......[Property] Floor threshold for No-Sync mode (500K), Double, 0.0 to 1000000000.0

      Eye:Cfg:FloorSync........[Property] Floor threshold for Sync mode (500K), Double, 0.0 to 1000000000.0

      Eye:Cfg:Height...........[Property] Acquisition Voltage height, Double, (RO)

      Eye:Cfg:Offset...........[Property] Acquisition Time offset, Double, (RO)

      Eye:Cfg:PerDiv...........[Property] Span per division, Double[2], 1.000 to 1000.000

      Eye:Cfg:Persist..........[Property] Persistence, Int, 0 to 5

      Eye:Cfg:Rows.............[Property] Rows in Image, Int, 10 to 1000

      Eye:Cfg:ShowRaw..........[Property] Show Raw Data, Bool

      Eye:Cfg:Span.............[Property] Acquisition Time span, Double, (RO)

      Eye:Cfg:ThreshSettle.....[Property] Threshold Settle Time, Int, 1 to 10, usec

      Eye:Cfg:UseClip..........[Property] Use Clipping for Floor level, Bool

    Eye:Ch0: [Category] Eye Channel, (IsClass)

      Eye:Ch0:Binary...........[Property] Binary Data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Eye:Ch0:Scale............[Property] Scale ratio percentage, Double, 10.000 to 1000.000, %

      Eye:Ch0:Show.............[Property] Show trace, Bool

      Eye:Ch0:TimeOffs.........[Property] Time Offset, Double, 0.000 to 1000.000, ps

      Eye:Ch0:VoltOffs.........[Property] Volt Offset, Double, -1000.000 to 1000.000, mV

      Eye:Ch0:Jpg..............[Method] PelaEye Jpg Image (HasPathResponse)

    Eye:Ch1: [Category] Eye Channel, (IsClass)

      Eye:Ch1:Binary...........[Property] Binary Data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Eye:Ch1:Scale............[Property] Scale ratio percentage, Double, 10.000 to 1000.000, %

      Eye:Ch1:Show.............[Property] Show trace, Bool

      Eye:Ch1:TimeOffs.........[Property] Time Offset, Double, 0.000 to 1000.000, ps

      Eye:Ch1:VoltOffs.........[Property] Volt Offset, Double, -1000.000 to 1000.000, mV

      Eye:Ch1:Jpg..............[Method] PelaEye Jpg Image (HasPathResponse)

    Eye:Chart: [Category] Chart View, (IsClass)

      Eye:Chart:Bottom.........[Property] Chart Bottom, Double, -2000.00 to 2000.00, mV

      Eye:Chart:CursAvail......[Property] Chart Cursor Available, Bool[11], (RO)

      Eye:Chart:CursEnabled....[Property] Chart Cursor Enabled, Bool[11]

      Eye:Chart:CursLabel......[Property] Chart Cursor Label, String[11], (RO)

      Eye:Chart:CursValue......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Eye:Chart:Height.........[Property] Chart Height, Double, 10.00 to 4000.00, mV

      Eye:Chart:Left...........[Property] Chart Left, Double, 0.00 to 400.00, ps

      Eye:Chart:Limits.........[Property] Chart Limits (LRBT), Double[4], (RO)

      Eye:Chart:Locked.........[Property] Chart Locked, Bool

      Eye:Chart:Logscale.......[Property] Chart LogScale, Bool

      Eye:Chart:Scroll.........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Eye:Chart:ShowMemory.....[Property] Show memories, Bool

      Eye:Chart:ShowOverlays...[Property] Show overlays, Bool

      Eye:Chart:Title..........[Property] Chart Title, String, (RO)

      Eye:Chart:Width..........[Property] Chart Width, Double, 10.00 to 400.00, ps


MaxT: [Category] MaxT ELA Application

    MaxT:Ch0: [Category] Ch0 Category, (IsClass)

      MaxT:Ch0:Binary..........[Property] Binary Data, float[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      MaxT:Ch0:BlockSize.......[Property] Block Size, Int, (RO)

      MaxT:Ch0:Bottom..........[Property] Chart Bottom, Double, 0 to 1000, , (NoSave)

      MaxT:Ch0:CursAvail.......[Property] Chart Cursor Available, Bool[11], (RO)

      MaxT:Ch0:CursEnabled.....[Property] Chart Cursor Enabled, Bool[11]

      MaxT:Ch0:CursLabel.......[Property] Chart Cursor Label, String[11], (RO)

      MaxT:Ch0:CursValue.......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      MaxT:Ch0:Enabled.........[Property] Enable processor, Bool, (RO)

      MaxT:Ch0:Height..........[Property] Chart Height, Double, 1 to 1000, , (NoSave)

      MaxT:Ch0:Interval........[Property] Update interval, Double, 1.0 to 10000.0, sec

      MaxT:Ch0:Left............[Property] Chart Left, Double, 10 to 10000, , (NoSave)

      MaxT:Ch0:Limits..........[Property] Chart Limits (LRBT), Double[4], (RO)

      MaxT:Ch0:Locked..........[Property] Chart Locked, Bool

      MaxT:Ch0:Logscale........[Property] Chart LogScale, Bool

      MaxT:Ch0:Reclen..........[Property] Record Length, Int, 10 to 3000

      MaxT:Ch0:Report..........[Property] Report-TotalBlocks, String, (RO, NoQuote)

      MaxT:Ch0:Scroll..........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      MaxT:Ch0:Serial..........[Property] Serial Number of Integration, Int, (RO)

      MaxT:Ch0:ShowMemory......[Property] Show memories, Bool

      MaxT:Ch0:ShowOverlays....[Property] Show overlays, Bool

      MaxT:Ch0:ShowSettings....[Property] Show Settings, Bool, (NoSave)

      MaxT:Ch0:Status..........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      MaxT:Ch0:Title...........[Property] Chart Title, String, (RO)

      MaxT:Ch0:Width...........[Property] Chart Width, Double, 10 to 10000, , (NoSave)

      MaxT:Ch0:Csv.............[Method] Download CSV File (HasPathResponse)

      MaxT:Ch0:Fit.............[Method] Fit chart to data

    MaxT:Ch1: [Category] Ch1 Category, (IsClass)

      MaxT:Ch1:Binary..........[Property] Binary Data, float[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      MaxT:Ch1:BlockSize.......[Property] Block Size, Int, (RO)

      MaxT:Ch1:Bottom..........[Property] Chart Bottom, Double, 0 to 1000, , (NoSave)

      MaxT:Ch1:CursAvail.......[Property] Chart Cursor Available, Bool[11], (RO)

      MaxT:Ch1:CursEnabled.....[Property] Chart Cursor Enabled, Bool[11]

      MaxT:Ch1:CursLabel.......[Property] Chart Cursor Label, String[11], (RO)

      MaxT:Ch1:CursValue.......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      MaxT:Ch1:Enabled.........[Property] Enable processor, Bool, (RO)

      MaxT:Ch1:Height..........[Property] Chart Height, Double, 1 to 1000, , (NoSave)

      MaxT:Ch1:Interval........[Property] Update interval, Double, 1.0 to 10000.0, sec

      MaxT:Ch1:Left............[Property] Chart Left, Double, 10 to 10000, , (NoSave)

      MaxT:Ch1:Limits..........[Property] Chart Limits (LRBT), Double[4], (RO)

      MaxT:Ch1:Locked..........[Property] Chart Locked, Bool

      MaxT:Ch1:Logscale........[Property] Chart LogScale, Bool

      MaxT:Ch1:Reclen..........[Property] Record Length, Int, 10 to 3000

      MaxT:Ch1:Report..........[Property] Report-TotalBlocks, String, (RO, NoQuote)

      MaxT:Ch1:Scroll..........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      MaxT:Ch1:Serial..........[Property] Serial Number of Integration, Int, (RO)

      MaxT:Ch1:ShowMemory......[Property] Show memories, Bool

      MaxT:Ch1:ShowOverlays....[Property] Show overlays, Bool

      MaxT:Ch1:ShowSettings....[Property] Show Settings, Bool, (NoSave)

      MaxT:Ch1:Status..........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      MaxT:Ch1:Title...........[Property] Chart Title, String, (RO)

      MaxT:Ch1:Width...........[Property] Chart Width, Double, 10 to 10000, , (NoSave)

      MaxT:Ch1:Csv.............[Method] Download CSV File (HasPathResponse)

      MaxT:Ch1:Fit.............[Method] Fit chart to data

    MaxT:Cmb: [Category] Combined Category, (IsClass)

      MaxT:Cmb:Binary..........[Property] Binary Data, float[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      MaxT:Cmb:BlockSize.......[Property] Block Size, Int, (RO)

      MaxT:Cmb:Bottom..........[Property] Chart Bottom, Double, 0 to 1000, , (NoSave)

      MaxT:Cmb:CursAvail.......[Property] Chart Cursor Available, Bool[11], (RO)

      MaxT:Cmb:CursEnabled.....[Property] Chart Cursor Enabled, Bool[11]

      MaxT:Cmb:CursLabel.......[Property] Chart Cursor Label, String[11], (RO)

      MaxT:Cmb:CursValue.......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      MaxT:Cmb:Enabled.........[Property] Enable processor, Bool, (RO)

      MaxT:Cmb:Height..........[Property] Chart Height, Double, 1 to 1000, , (NoSave)

      MaxT:Cmb:Interval........[Property] Update interval, Double, 1.0 to 10000.0, sec

      MaxT:Cmb:Left............[Property] Chart Left, Double, 10 to 10000, , (NoSave)

      MaxT:Cmb:Limits..........[Property] Chart Limits (LRBT), Double[4], (RO)

      MaxT:Cmb:Locked..........[Property] Chart Locked, Bool

      MaxT:Cmb:Logscale........[Property] Chart LogScale, Bool

      MaxT:Cmb:Reclen..........[Property] Record Length, Int, 10 to 3000

      MaxT:Cmb:Report..........[Property] Report-TotalBlocks, String, (RO, NoQuote)

      MaxT:Cmb:Scroll..........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      MaxT:Cmb:Serial..........[Property] Serial Number of Integration, Int, (RO)

      MaxT:Cmb:ShowMemory......[Property] Show memories, Bool

      MaxT:Cmb:ShowOverlays....[Property] Show overlays, Bool

      MaxT:Cmb:ShowSettings....[Property] Show Settings, Bool, (NoSave)

      MaxT:Cmb:Status..........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      MaxT:Cmb:Title...........[Property] Chart Title, String, (RO)

      MaxT:Cmb:Width...........[Property] Chart Width, Double, 10 to 10000, , (NoSave)

      MaxT:Cmb:Csv.............[Method] Download CSV File (HasPathResponse)

      MaxT:Cmb:Fit.............[Method] Fit chart to data


Mod: [Category] Modulo ELA Application

    Mod:Ch0: [Category] Ch0 Category, (IsClass)

      Mod:Ch0:Binary...........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Mod:Ch0:Bins.............[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Mod:Ch0:Bottom...........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Mod:Ch0:CursAvail........[Property] Chart Cursor Available, Bool[11], (RO)

      Mod:Ch0:CursEnabled......[Property] Chart Cursor Enabled, Bool[11]

      Mod:Ch0:CursLabel........[Property] Chart Cursor Label, String[11], (RO)

      Mod:Ch0:CursValue........[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Mod:Ch0:Enabled..........[Property] Enable processor, Bool, (RO)

      Mod:Ch0:Height...........[Property] Chart Height, Double, 1 to 2147483647, 

      Mod:Ch0:History..........[Property] Histogram history length, Int, 0 to 100000

      Mod:Ch0:HReport..........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Mod:Ch0:HSeq.............[Property] Histogram Sequence number, Int, (RO, NoSave)

      Mod:Ch0:Left.............[Property] Chart Left, Double, 0 to 100000000000000, 

      Mod:Ch0:Limits...........[Property] Chart Limits (LRBT), Double[4], (RO)

      Mod:Ch0:Locked...........[Property] Chart Locked, Bool

      Mod:Ch0:Logscale.........[Property] Chart LogScale, Bool

      Mod:Ch0:ModSize..........[Property] Modulo Size, Int, 0 to 4294967295

      Mod:Ch0:ModType..........[Property] Modulo Type, Enum <Pattern, Manual>

      Mod:Ch0:Offset...........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Mod:Ch0:Pattern..........[Property] Pattern Type, String, (RO)

      Mod:Ch0:Report...........[Property] Report-ModSize,ModPattern, String, (RO, NoQuote)

      Mod:Ch0:Resol............[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Mod:Ch0:Scroll...........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Mod:Ch0:Seed.............[Property] Pattern Seed, Int, (RO)

      Mod:Ch0:ShowMemory.......[Property] Show memories, Bool

      Mod:Ch0:ShowOverlays.....[Property] Show overlays, Bool

      Mod:Ch0:ShowSettings.....[Property] Show Settings, Bool, (NoSave)

      Mod:Ch0:Status...........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Mod:Ch0:Title............[Property] Chart Title, String, (RO)

      Mod:Ch0:Width............[Property] Chart Width, Double, 1 to 100000000000000, 

      Mod:Ch0:Csv..............[Method] Download CSV File (HasPathResponse)

      Mod:Ch0:Fit..............[Method] Fit chart to data

      Mod:Ch0:MapRange.........[Method] Map histogram to fit range

      Mod:Ch0:Reset............[Method] Reset chart

    Mod:Ch1: [Category] Ch1 Category, (IsClass)

      Mod:Ch1:Binary...........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Mod:Ch1:Bins.............[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Mod:Ch1:Bottom...........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Mod:Ch1:CursAvail........[Property] Chart Cursor Available, Bool[11], (RO)

      Mod:Ch1:CursEnabled......[Property] Chart Cursor Enabled, Bool[11]

      Mod:Ch1:CursLabel........[Property] Chart Cursor Label, String[11], (RO)

      Mod:Ch1:CursValue........[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Mod:Ch1:Enabled..........[Property] Enable processor, Bool, (RO)

      Mod:Ch1:Height...........[Property] Chart Height, Double, 1 to 2147483647, 

      Mod:Ch1:History..........[Property] Histogram history length, Int, 0 to 100000

      Mod:Ch1:HReport..........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Mod:Ch1:HSeq.............[Property] Histogram Sequence number, Int, (RO, NoSave)

      Mod:Ch1:Left.............[Property] Chart Left, Double, 0 to 100000000000000, 

      Mod:Ch1:Limits...........[Property] Chart Limits (LRBT), Double[4], (RO)

      Mod:Ch1:Locked...........[Property] Chart Locked, Bool

      Mod:Ch1:Logscale.........[Property] Chart LogScale, Bool

      Mod:Ch1:ModSize..........[Property] Modulo Size, Int, 0 to 4294967295

      Mod:Ch1:ModType..........[Property] Modulo Type, Enum <Pattern, Manual>

      Mod:Ch1:Offset...........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Mod:Ch1:Pattern..........[Property] Pattern Type, String, (RO)

      Mod:Ch1:Report...........[Property] Report-ModSize,ModPattern, String, (RO, NoQuote)

      Mod:Ch1:Resol............[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Mod:Ch1:Scroll...........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Mod:Ch1:Seed.............[Property] Pattern Seed, Int, (RO)

      Mod:Ch1:ShowMemory.......[Property] Show memories, Bool

      Mod:Ch1:ShowOverlays.....[Property] Show overlays, Bool

      Mod:Ch1:ShowSettings.....[Property] Show Settings, Bool, (NoSave)

      Mod:Ch1:Status...........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Mod:Ch1:Title............[Property] Chart Title, String, (RO)

      Mod:Ch1:Width............[Property] Chart Width, Double, 1 to 100000000000000, 

      Mod:Ch1:Csv..............[Method] Download CSV File (HasPathResponse)

      Mod:Ch1:Fit..............[Method] Fit chart to data

      Mod:Ch1:MapRange.........[Method] Map histogram to fit range

      Mod:Ch1:Reset............[Method] Reset chart

    Mod:Cmb: [Category] Combined Category, (IsClass)

      Mod:Cmb:Binary...........[Property] Packed histogram binary data, char[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Mod:Cmb:Bins.............[Property] Histogram bin count, Int, 0 to 5000, (NoSave)

      Mod:Cmb:Bottom...........[Property] Chart Bottom, Double, 0 to 2147483647, 

      Mod:Cmb:CursAvail........[Property] Chart Cursor Available, Bool[11], (RO)

      Mod:Cmb:CursEnabled......[Property] Chart Cursor Enabled, Bool[11]

      Mod:Cmb:CursLabel........[Property] Chart Cursor Label, String[11], (RO)

      Mod:Cmb:CursValue........[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Mod:Cmb:Enabled..........[Property] Enable processor, Bool, (RO)

      Mod:Cmb:Height...........[Property] Chart Height, Double, 1 to 2147483647, 

      Mod:Cmb:History..........[Property] Histogram history length, Int, 0 to 100000

      Mod:Cmb:HReport..........[Property] Report-Pop,Ovrflw,Min,Max,Start,End,HistryLen, String, (RO, NoQuote)

      Mod:Cmb:HSeq.............[Property] Histogram Sequence number, Int, (RO, NoSave)

      Mod:Cmb:Left.............[Property] Chart Left, Double, 0 to 100000000000000, 

      Mod:Cmb:Limits...........[Property] Chart Limits (LRBT), Double[4], (RO)

      Mod:Cmb:Locked...........[Property] Chart Locked, Bool

      Mod:Cmb:Logscale.........[Property] Chart LogScale, Bool

      Mod:Cmb:ModSize..........[Property] Modulo Size, Int, 0 to 4294967295

      Mod:Cmb:ModType..........[Property] Modulo Type, Enum <Pattern, Manual>

      Mod:Cmb:Offset...........[Property] Histogram bin offset, Double, 0 to 100000000000000, (NoSave)

      Mod:Cmb:Pattern..........[Property] Pattern Type, String, (RO)

      Mod:Cmb:Report...........[Property] Report-ModSize,ModPattern, String, (RO, NoQuote)

      Mod:Cmb:Resol............[Property] Histogram bin resolution, Double, 1.000000 to 100000000000000.000000, (NoSave)

      Mod:Cmb:Scroll...........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Mod:Cmb:Seed.............[Property] Pattern Seed, Int, (RO)

      Mod:Cmb:ShowMemory.......[Property] Show memories, Bool

      Mod:Cmb:ShowOverlays.....[Property] Show overlays, Bool

      Mod:Cmb:ShowSettings.....[Property] Show Settings, Bool, (NoSave)

      Mod:Cmb:Status...........[Property] Ela Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Mod:Cmb:Title............[Property] Chart Title, String, (RO)

      Mod:Cmb:Width............[Property] Chart Width, Double, 1 to 100000000000000, 

      Mod:Cmb:Csv..............[Method] Download CSV File (HasPathResponse)

      Mod:Cmb:Fit..............[Method] Fit chart to data

      Mod:Cmb:MapRange.........[Method] Map histogram to fit range

      Mod:Cmb:Reset............[Method] Reset chart


Patt: [Category] User Patterns

    Patt:File..................[Property] User pattern filename, String[2], (RO)

    Patt:Folder................[Property] Current folder, String

    Patt:GuiCh.................[Property] Gui channel, Enum <Ch0, Ch1, Dual>

    Patt:GuiFormat.............[Property] Gui number format, Enum <Hex, Decimal, Octal, Binary>

    Patt:GuiSymbols............[Property] Gui number of symbols, Int, Min 1, (Comma)

    Patt:GuiSymbolSize.........[Property] Gui bits per symbol, Int, 1 to 32, (Comma)

    Patt:GuiType...............[Property] Gui file type, Enum <All, Pattern, Playlist>

    Patt:RestoreBitShift.......[Property] Restore bit shift, Int[3], -255 to 255, (NoEvent)

    Patt:RestoreFile...........[Property] Restore user pattern files, String[3], (NoEvent)

    Patt:RootFolder............[Property] User Patterns root folder, String, (RO)

    Patt:StatusMsg.............[Property] Status message, String, (RO)

    Patt:VerifyMsg.............[Property] Verify message, String, (RO)

    Patt:ClearStatusMsg........[Method] Clear status message (NoAuth)

    Patt:ClearVerifyMsg........[Method] Clear verify message (NoAuth)

    Patt:Copy..................[Method] File copy

    Patt:Delete................[Method] File delete

    Patt:Deploy................[Method] Deploy pattern

    Patt:Fetch.................[Method] Fetch file (NoAuth,HasBinaryResponse)

    Patt:FetchDir..............[Method] Fetch directory (NoAuth,HasBinaryStringResponse)

    Patt:Grab..................[Method] Grab pattern

    Patt:NewFolder.............[Method] New folder

    Patt:Rename................[Method] File rename

    Patt:Save..................[Method] File save (HasBinaryInput)

    Patt:Verify................[Method] Verify file (HasBinaryInput)


RLen: [Category] Data Run Length Application

    RLen:Ch0: [Category] Ch0 Category, (IsClass)

      RLen:Ch0:Binary..........[Property] Histogram binary data, u32[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      RLen:Ch0:BitPop..........[Property] Bit population, LongLong, (RO, NoSave)

      RLen:Ch0:Bottom..........[Property] Chart Bottom, Double, 0 to 2000001000, 

      RLen:Ch0:CursAvail.......[Property] Chart Cursor Available, Bool[11], (RO)

      RLen:Ch0:CursEnabled.....[Property] Chart Cursor Enabled, Bool[11]

      RLen:Ch0:CursLabel.......[Property] Chart Cursor Label, String[11], (RO)

      RLen:Ch0:CursValue.......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      RLen:Ch0:Enabled.........[Property] Enable processor, Bool, (RO)

      RLen:Ch0:Height..........[Property] Chart Height, Double, 1 to 2000001000, 

      RLen:Ch0:Left............[Property] Chart Left, Double, 0 to 510, 

      RLen:Ch0:Limits..........[Property] Chart Limits (LRBT), Double[4], (RO)

      RLen:Ch0:Locked..........[Property] Chart Locked, Bool

      RLen:Ch0:Logscale........[Property] Chart LogScale, Bool

      RLen:Ch0:RunType.........[Property] Run length type, Enum <Space, Mark>

      RLen:Ch0:Scroll..........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      RLen:Ch0:ShowMemory......[Property] Show memories, Bool

      RLen:Ch0:ShowOverlays....[Property] Show overlays, Bool

      RLen:Ch0:ShowSettings....[Property] Show Settings, Bool, (NoSave)

      RLen:Ch0:Status..........[Property] Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      RLen:Ch0:Title...........[Property] Chart Title, String, (RO)

      RLen:Ch0:Used............[Property] Number Used, Int, (RO, NoSave)

      RLen:Ch0:Width...........[Property] Chart Width, Double, 1 to 510, 

      RLen:Ch0:Csv.............[Method] Download CSV File (HasPathResponse)

      RLen:Ch0:Fit.............[Method] Fit chart to data

      RLen:Ch0:Reset...........[Method] Reset chart

    RLen:Ch1: [Category] Ch1 Category, (IsClass)

      RLen:Ch1:Binary..........[Property] Histogram binary data, u32[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      RLen:Ch1:BitPop..........[Property] Bit population, LongLong, (RO, NoSave)

      RLen:Ch1:Bottom..........[Property] Chart Bottom, Double, 0 to 2000001000, 

      RLen:Ch1:CursAvail.......[Property] Chart Cursor Available, Bool[11], (RO)

      RLen:Ch1:CursEnabled.....[Property] Chart Cursor Enabled, Bool[11]

      RLen:Ch1:CursLabel.......[Property] Chart Cursor Label, String[11], (RO)

      RLen:Ch1:CursValue.......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      RLen:Ch1:Enabled.........[Property] Enable processor, Bool, (RO)

      RLen:Ch1:Height..........[Property] Chart Height, Double, 1 to 2000001000, 

      RLen:Ch1:Left............[Property] Chart Left, Double, 0 to 510, 

      RLen:Ch1:Limits..........[Property] Chart Limits (LRBT), Double[4], (RO)

      RLen:Ch1:Locked..........[Property] Chart Locked, Bool

      RLen:Ch1:Logscale........[Property] Chart LogScale, Bool

      RLen:Ch1:RunType.........[Property] Run length type, Enum <Space, Mark>

      RLen:Ch1:Scroll..........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      RLen:Ch1:ShowMemory......[Property] Show memories, Bool

      RLen:Ch1:ShowOverlays....[Property] Show overlays, Bool

      RLen:Ch1:ShowSettings....[Property] Show Settings, Bool, (NoSave)

      RLen:Ch1:Status..........[Property] Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      RLen:Ch1:Title...........[Property] Chart Title, String, (RO)

      RLen:Ch1:Used............[Property] Number Used, Int, (RO, NoSave)

      RLen:Ch1:Width...........[Property] Chart Width, Double, 1 to 510, 

      RLen:Ch1:Csv.............[Method] Download CSV File (HasPathResponse)

      RLen:Ch1:Fit.............[Method] Fit chart to data

      RLen:Ch1:Reset...........[Method] Reset chart

    RLen:Cmb: [Category] Combined Category, (IsClass)

      RLen:Cmb:Binary..........[Property] Histogram binary data, u32[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      RLen:Cmb:BitPop..........[Property] Bit population, LongLong, (RO, NoSave)

      RLen:Cmb:Bottom..........[Property] Chart Bottom, Double, 0 to 2000001000, 

      RLen:Cmb:CursAvail.......[Property] Chart Cursor Available, Bool[11], (RO)

      RLen:Cmb:CursEnabled.....[Property] Chart Cursor Enabled, Bool[11]

      RLen:Cmb:CursLabel.......[Property] Chart Cursor Label, String[11], (RO)

      RLen:Cmb:CursValue.......[Property] Chart Cursor Value, Double[11], (NeverDirty)

      RLen:Cmb:Enabled.........[Property] Enable processor, Bool, (RO)

      RLen:Cmb:Height..........[Property] Chart Height, Double, 1 to 2000001000, 

      RLen:Cmb:Left............[Property] Chart Left, Double, 0 to 510, 

      RLen:Cmb:Limits..........[Property] Chart Limits (LRBT), Double[4], (RO)

      RLen:Cmb:Locked..........[Property] Chart Locked, Bool

      RLen:Cmb:Logscale........[Property] Chart LogScale, Bool

      RLen:Cmb:RunType.........[Property] Run length type, Enum <Space, Mark>

      RLen:Cmb:Scroll..........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      RLen:Cmb:ShowMemory......[Property] Show memories, Bool

      RLen:Cmb:ShowOverlays....[Property] Show overlays, Bool

      RLen:Cmb:ShowSettings....[Property] Show Settings, Bool, (NoSave)

      RLen:Cmb:Status..........[Property] Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      RLen:Cmb:Title...........[Property] Chart Title, String, (RO)

      RLen:Cmb:Used............[Property] Number Used, Int, (RO, NoSave)

      RLen:Cmb:Width...........[Property] Chart Width, Double, 1 to 510, 

      RLen:Cmb:Csv.............[Method] Download CSV File (HasPathResponse)

      RLen:Cmb:Fit.............[Method] Fit chart to data

      RLen:Cmb:Reset...........[Method] Reset chart


Stat: [Category] Data application statistics Application

    Stat:Bits..................[Property] Bit Count Result, LongLong[3], (RO, Comma)

    Stat:Enabled...............[Property] Enable processor, Bool[3], (RO)

    Stat:MarkDensity...........[Property] Mark Density results, Double[3], %, (RO)

    Stat:Marks.................[Property] Marks Count Result, LongLong[3], (RO, Comma)

    Stat:Report................[Property] Statistics report, String, (RO, NoQuote)

    Stat:Status................[Property] Ela Status, Enum[3] <NotAvail, Disabled, Stopped, Running>, (RO)


Wander: [Category] Data Wander Application

    Wander:Ch0: [Category] Ch0 Category, (IsClass)

      Wander:Ch0:Binary........[Property] Histogram binary data, u32[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Wander:Ch0:BitPop........[Property] Bit population, LongLong, (RO, NoSave)

      Wander:Ch0:Bottom........[Property] Chart Bottom, Double, 0 to 2000001000, 

      Wander:Ch0:CursAvail.....[Property] Chart Cursor Available, Bool[11], (RO)

      Wander:Ch0:CursEnabled...[Property] Chart Cursor Enabled, Bool[11]

      Wander:Ch0:CursLabel.....[Property] Chart Cursor Label, String[11], (RO)

      Wander:Ch0:CursValue.....[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Wander:Ch0:Enabled.......[Property] Enable processor, Bool, (RO)

      Wander:Ch0:Height........[Property] Chart Height, Double, 1 to 2000001000, 

      Wander:Ch0:Largest.......[Property] Largest disparity, Double, %, (RO, NoSave)

      Wander:Ch0:Left..........[Property] Chart Left, Double, 0 to 105, 

      Wander:Ch0:Limits........[Property] Chart Limits (LRBT), Double[4], (RO)

      Wander:Ch0:Locked........[Property] Chart Locked, Bool

      Wander:Ch0:Logscale......[Property] Chart LogScale, Bool

      Wander:Ch0:Mode..........[Property] Wander mode, NRZ or PAM4, Enum <TwoLevel, FourLevel>

      Wander:Ch0:Order.........[Property] Symbol order, Enum <MsbFirst, LsbFirst>

      Wander:Ch0:Scroll........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Wander:Ch0:ShowMemory....[Property] Show memories, Bool

      Wander:Ch0:ShowOverlays..[Property] Show overlays, Bool

      Wander:Ch0:ShowSettings..[Property] Show Settings, Bool, (NoSave)

      Wander:Ch0:Smallest......[Property] Smallest disparity, Double, %, (RO, NoSave)

      Wander:Ch0:Status........[Property] Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Wander:Ch0:Title.........[Property] Chart Title, String, (RO)

      Wander:Ch0:Width.........[Property] Chart Width, Double, 1 to 105, 

      Wander:Ch0:Window........[Property] Bit window, Int, 1000 to 50000, bits

      Wander:Ch0:Csv...........[Method] Download CSV File (HasPathResponse)

      Wander:Ch0:Fit...........[Method] Fit chart to data

      Wander:Ch0:Reset.........[Method] Reset chart

    Wander:Ch1: [Category] Ch1 Category, (IsClass)

      Wander:Ch1:Binary........[Property] Histogram binary data, u32[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Wander:Ch1:BitPop........[Property] Bit population, LongLong, (RO, NoSave)

      Wander:Ch1:Bottom........[Property] Chart Bottom, Double, 0 to 2000001000, 

      Wander:Ch1:CursAvail.....[Property] Chart Cursor Available, Bool[11], (RO)

      Wander:Ch1:CursEnabled...[Property] Chart Cursor Enabled, Bool[11]

      Wander:Ch1:CursLabel.....[Property] Chart Cursor Label, String[11], (RO)

      Wander:Ch1:CursValue.....[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Wander:Ch1:Enabled.......[Property] Enable processor, Bool, (RO)

      Wander:Ch1:Height........[Property] Chart Height, Double, 1 to 2000001000, 

      Wander:Ch1:Largest.......[Property] Largest disparity, Double, %, (RO, NoSave)

      Wander:Ch1:Left..........[Property] Chart Left, Double, 0 to 105, 

      Wander:Ch1:Limits........[Property] Chart Limits (LRBT), Double[4], (RO)

      Wander:Ch1:Locked........[Property] Chart Locked, Bool

      Wander:Ch1:Logscale......[Property] Chart LogScale, Bool

      Wander:Ch1:Mode..........[Property] Wander mode, NRZ or PAM4, Enum <TwoLevel, FourLevel>

      Wander:Ch1:Order.........[Property] Symbol order, Enum <MsbFirst, LsbFirst>

      Wander:Ch1:Scroll........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Wander:Ch1:ShowMemory....[Property] Show memories, Bool

      Wander:Ch1:ShowOverlays..[Property] Show overlays, Bool

      Wander:Ch1:ShowSettings..[Property] Show Settings, Bool, (NoSave)

      Wander:Ch1:Smallest......[Property] Smallest disparity, Double, %, (RO, NoSave)

      Wander:Ch1:Status........[Property] Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Wander:Ch1:Title.........[Property] Chart Title, String, (RO)

      Wander:Ch1:Width.........[Property] Chart Width, Double, 1 to 105, 

      Wander:Ch1:Window........[Property] Bit window, Int, 1000 to 50000, bits

      Wander:Ch1:Csv...........[Method] Download CSV File (HasPathResponse)

      Wander:Ch1:Fit...........[Method] Fit chart to data

      Wander:Ch1:Reset.........[Method] Reset chart

    Wander:Cmb: [Category] Combined Category, (IsClass)

      Wander:Cmb:Binary........[Property] Histogram binary data, u32[], Binary, (RO, NoEvent, NoSave, Bin, Stealth)

      Wander:Cmb:BitPop........[Property] Bit population, LongLong, (RO, NoSave)

      Wander:Cmb:Bottom........[Property] Chart Bottom, Double, 0 to 2000001000, 

      Wander:Cmb:CursAvail.....[Property] Chart Cursor Available, Bool[11], (RO)

      Wander:Cmb:CursEnabled...[Property] Chart Cursor Enabled, Bool[11]

      Wander:Cmb:CursLabel.....[Property] Chart Cursor Label, String[11], (RO)

      Wander:Cmb:CursValue.....[Property] Chart Cursor Value, Double[11], (NeverDirty)

      Wander:Cmb:Enabled.......[Property] Enable processor, Bool, (RO)

      Wander:Cmb:Height........[Property] Chart Height, Double, 1 to 2000001000, 

      Wander:Cmb:Largest.......[Property] Largest disparity, Double, %, (RO, NoSave)

      Wander:Cmb:Left..........[Property] Chart Left, Double, 0 to 105, 

      Wander:Cmb:Limits........[Property] Chart Limits (LRBT), Double[4], (RO)

      Wander:Cmb:Locked........[Property] Chart Locked, Bool

      Wander:Cmb:Logscale......[Property] Chart LogScale, Bool

      Wander:Cmb:Mode..........[Property] Wander mode, NRZ or PAM4, Enum <TwoLevel, FourLevel>

      Wander:Cmb:Order.........[Property] Symbol order, Enum <MsbFirst, LsbFirst>

      Wander:Cmb:Scroll........[Property] Chart Scroll Mode, Enum <None, X1, X2, X3, X4, DX12, DX34, XPan, XScale, Y1, Y2, Y3, Y4, DY12, DY34, YPan, YScale, P1, P2, P3>

      Wander:Cmb:ShowMemory....[Property] Show memories, Bool

      Wander:Cmb:ShowOverlays..[Property] Show overlays, Bool

      Wander:Cmb:ShowSettings..[Property] Show Settings, Bool, (NoSave)

      Wander:Cmb:Smallest......[Property] Smallest disparity, Double, %, (RO, NoSave)

      Wander:Cmb:Status........[Property] Data Status, Enum <NotAvail, Disabled, Stopped, Running>, (RO)

      Wander:Cmb:Title.........[Property] Chart Title, String, (RO)

      Wander:Cmb:Width.........[Property] Chart Width, Double, 1 to 105, 

      Wander:Cmb:Window........[Property] Bit window, Int, 1000 to 50000, bits

      Wander:Cmb:Csv...........[Method] Download CSV File (HasPathResponse)

      Wander:Cmb:Fit...........[Method] Fit chart to data

      Wander:Cmb:Reset.........[Method] Reset chart